ngHobbies
SINGLE BL-CTRL V3.0 2XL
| IMPORTANT | Use FlightCtrl Firmware V2.02 (or greater), otherwise read the instructions in the wiki ! |
| •voltage | 10 to 30V -> 3 -7S Lipo |
| • current | up to 60A with appropriate cooling |
| • Silent Start | test tone at startup can be disabled |
| • hole | 3mm |
| • Dimensions (W x H ) | approx 75mm x 26mm (without capacitors) |
| • Dimensions (W x H ) | approx 96mm x 26mm ( with capacitors) |
| • weight | 15g (with capacitors) |
Note: The BL-Ctrl 3.0 controller is specifically designed and optimized for our motors. For maximum stability of the MikroKopter setpoints are set almost instantaneously on the motor. If other motors (especially larger power classes) are used with this controller, this fast change of setpoints can easily lead to very high peak currents, which bring the BL-Ctrl control to the limit or an overload. This is no fault of BL-Ctrl3.0 controller, but a systemic property., This new version has the following features:, Dimensions:, The following items are included in this kit:,
Extremely fast brushless controller version V3 for any MikroKopter with ...ngHobbies
3DR PIXHAWK AUTOPILOT W/O GPS AND PPM ENCODER
| • Weight | 38g (1.31oz) |
| • Width | 50mm (1.96") |
| • Thickness | 15.5mm (.613") |
| • Length | 81.5mm (3.21") |
Note: Pixhawk is a PPM-input autopilot, which means that it gets RC input from a single cable to the receiver, either via the PPM port, the Futaba S.BUS port, or the special satellite receiver port for Spektrum gear. Most modern RC receivers (and all those sold by 3D Robotics) allow for PPM output, but some, such as non-S.BUS Futaba receivers, do not., Pixhawk includes:, • Pixhawk autopilot, Microprocessor:, • 32-bit STM32F427 Cortex M4 core with FPU, Sensors:, • ST Micro L3GD20 3-axis 16-bit gyroscope, Interfaces:, • 5x UART (serial ports), one high-power capable, 2x with HW flow control, Power System:, • Ideal diode controller with automatic failover, Weight and Dimensions:,
Pixhawk is an advanced autopilot system designed by the PX4 ...ngHobbies
ALTITUDERC NANO 25MW 5.8GHZ TRANSMITTER
| Operating Frequencies | 5740, 5760, 5780, 5800, 5820, 5840, 5860MHz |
| Weight | 3 grams |
| Size | 23.6 x 20mm |
| Input voltage range | 3 - 12.6 V |
Parameters:, 25mW output power, Content of the package:, 1 x 25mW Transmitter module, Note:, The use and operation of this product in Canada and United States will require a HAM or Amateur radio license. Please check with your local authorities before purchasing this product.,
The 25mW transmitter designed by Altitude RC nano size is ...ngHobbies
400MW 910MHZ 1CHTRANSMITTER
| Please note | Please make sure that you obey Industry Canada regulations when using these transmitters in Canada. |
Features:, Frequency:, 910MHz, Number of Channels:, 1, Modulation:, FM, Transmission Range:, 1 km plus, Power Consumption:, 300mA, Output Power:, 400mW, Operation Voltage:, 12V, Power Supply:, 12V/500mA (not included), Antenna Connector:, SMA Connector, Weight:, 7.9 g, Dimensions:, 50.0 x 25.7 x 8.0 mm, Note:, While this transmitter might work with other 900Mhz receivers as well, please note only guarantee the above ranges and signal quality when used in conjuntion with the, Documentation:, Warranty:, 3 months, Note:, The use and operation of this product will require a valid HAM or Amateur radio license., Important note for Canada customers:, ,
Highly integrated 900 MHz, 400mW transmitter with digital display. Very ...ngHobbies
800MW 910MHZ 1CH TRANSMITTER
Features:, Frequency:, 910MHz, Number of Channels:, 1, Modulation:, FM, Transmission Range:, 1 km plus, Power Consumption:, 500mA, Output Power:, 800mW, Operation Voltage:, 12V, Power Supply:, 12V/500mA (not included), Antenna Connector:, SMA Connector, Weight:, 7.9 g, Dimensions:, 50.0 x 25.7 x 8.0 mm, Note:, While this transmitter might work with other 900Mhz receivers as well, please note only guarantee the above ranges and signal quality when used in conjuntion with the, Documentation:, Warranty:, 3 months, Note:, The use and operation of this product will require a HAM or Amateur radio license., Important note for Canada customers:,
If this transmitter is shipped to a USA address, it ...ngHobbies
1500MW 910MHZ 1CH TRANSMITTER
Features:, Frequency:, 910MHz, Number of Channels:, 1, Modulation:, FM, Transmission Range:, 2 km plus, Power Consumption:, 600mA, Output Power:, 1500mW, Operation Voltage:, 12V, Power Supply:, 12V/600mA (not included), Antenna Connector:, SMA Connector, Weight:, 7.9 g, Dimensions:, 70 x 25.7 x 8 mm, Note:, While this transmitter might work with other 900Mhz receivers as well, please note only guarantee the above ranges and signal quality when used in conjuntion with the, Documentation:, Warranty:, 6 months, Note:, The use and operation of this product will require a HAM or Amateur radio license., Important note for Canada customers:,
Highly integrated 910 MHz, 1500mW transmitter with digital display. Very ...ngHobbies
FATSHARK FCC APPROVED 5.8GHZ TRANSMITTER
| Operating Frequencies | 5740, 5760, 5780, 5800, 5820, 5840, 5860MHz |
| Weight | 29 grams |
| Size | 40 x 26 x 13mm |
| Input voltage range | 6 - 16 v |
Parameters:, 0.75mW output power, Content of the package:, 1 x cased transmitter module,
The Fat Shark FCC certified transmitter provides license free operation ...ngHobbies
VECTOR FLIGHT CONTROLLER + OSD WITH DEANS
| • FIXED WING and MULTIROTOR Flight Controller with GPS modes and RTH ◦Fixed wing | Traditional fixed wing, Elevon, and V-tail planes |
| ◦ Multirotor | Tricopter, Quadcopter, and Hexacopter |
| • COMPATIBLE | PCM, SPPM and S.BUS receiver support, with 4 types of RSSI |
| • FLEXIBLE | fly with or without your FPV equipment |
| • REDUCED WIRING | innovative wire harness with power distribution simplifies hookup |
| http | //www.rcgroups.com/forums/showthread.php?t=2032857 |
| http | //fpvlab.com/forums/showthread.php?22260-Vector-FPV-Controller-Everything-we-ve-all-dreamed-about |
| http | //eagletreesystems.com/Manuals/vector.pdf |
| http | //www.eagletreesystems.com/index.php?route=product/product&product_id=136 |
Years in the making, and built from the ground up with simplicity in mind, the Vector has everything we hobbyists have dreamed about for our recreational FPV models, in one small, lightweight easy to use product:, • SIMPLE to set up and operate "out of the box" for both fixed wing and multirotor, with no PC required, Join the online Vector discussion:, :, :,
• Built-in OSD with COLOR GRAPHICS! ◦OSD display is fully ...ngHobbies
VECTOR FLIGHT CONTROLLER + OSD WITH XT60
| • FIXED WING and MULTIROTOR Flight Controller with GPS modes and RTH ◦Fixed wing | Traditional fixed wing, Elevon, and V-tail planes |
| ◦ Multirotor | Tricopter, Quadcopter, and Hexacopter |
| • COMPATIBLE | PCM, SPPM and S.BUS receiver support, with 4 types of RSSI |
| • FLEXIBLE | fly with or without your FPV equipment |
| • REDUCED WIRING | innovative wire harness with power distribution simplifies hookup |
| http | //www.rcgroups.com/forums/showthread.php?t=2032857 |
| http | //fpvlab.com/forums/showthread.php?22260-Vector-FPV-Controller-Everything-we-ve-all-dreamed-about |
| http | //eagletreesystems.com/Manuals/vector.pdf |
| http | //www.eagletreesystems.com/index.php?route=product/product&product_id=136 |
Years in the making, and built from the ground up with simplicity in mind, the Vector has everything we hobbyists have dreamed about for our recreational FPV models, in one small, lightweight easy to use product:, • SIMPLE to set up and operate "out of the box" for both fixed wing and multirotor, with no PC required, Join the online Vector discussion:, :, :,
• Built-in OSD with COLOR GRAPHICS! ◦OSD display is fully ...ngHobbies
7" FPV DISPLAY, 23CH DUAL RX AND BUILT IN BATTERY
| The display is a 16 | 9 aspect ratio, but the incoming video can be configured to 16 |
| Panel size | 7.0 inch |
| Panel type | TFT LCD |
| Resolution | 800×480 |
| Backlight | LED |
| Batttery | built in 2200mAh 2 cell LiPo |
| Horizontal frequency range | 30～ 60 kHz |
| Field frequency range | 50 ～75 Hz |
| Dot pitch | 0.0642（W）×0.1790（H）mm |
| Brightness | 400cd/㎡ |
| Contrast ratio | 500 |
| Response time | 15 ms |
| Viewing angle | 70°/70°(L/R) 50°/60°（U/D) |
| Power requirement, input voltage | DC 6 ～18V middle pin positive |
| Power consumption | ≦ 7W |
| Operation temperature range | -20℃～60℃ |
| Storage temperature range | -30℃～70℃ |
| Dimension Unit size | 209（L）×147(W)×35(H) mm |
| Unit weight | 540 g |
| Connector type | standard SMA |
NGHobbies is happy to bring you this 5.8Ghz dual diversity 7" FPV display with built in battery specifically designed for FPV purposes as this display will not go "blue screen" when the wireless signal drops out for a few seconds. This is the first ground station monitor, designed specially for FPV outdoor use. With its high resolution (800*480), high contrast ratio (500:1) and brightness of 400cd/ ㎡ this is really the best choice for theFPV flyer who chooses to fly with a monitor instead of goggles., Specifications:, Display ratio: 16:9, Number of channels on 5.8Ghz: 32, Documentation:, Dip switch reference guide for channel selection,
The included hard case sun shade, with a plastic frame ...ngHobbies
700MW 2.4GHZ IMMERSIONRC TRANSMITTER (3CH)
| Operating Frequencies | 2396Mhz, 2410Mhz, 2430Mhz |
| Weight | 28 grams (without antenna) |
| Size | 57 x 34mm |
| Input voltage range | 6 - 25 v |
Parameters:, 700mW output power, Content of the package:, 1 x 700mW Transmitter module, Note:, The use and operation of this product in Canada and United States will require a HAM or Amateur radio license. Please check with your local authorities before purchasing this product.,
The new 2.4Ghz 700mW transmitter from ImmersionRC is bringing back ...ngHobbies
1.2 GHZ 8 DBI FLAT PATCH ANTENNA
| Frequency | 1080-1200 MHz |
| Gain | 8 dBi |
| Horizontal Beam Width | 75 degrees |
| Vertical Beam Width | 65 degrees |
| Impedance | 50 Ohm |
| Max. Input Power | 25 Watts |
| VSWR | < 1.5 |
| Weight | < 1 lb. (0.45 kg) |
| Dimensions | 8.5" x 8.5" x 1.2" (220 x 220 x 30 mm) |
| Radome Material | UV-inhibited Polymer |
| Flame Rating | UL 94HB |
| Mounting | Four ¼" Holes |
| Polarization | Horizontal and Vertical |
| Operating Temperature | -40° C to to 85° C (-40° F to 185° F) |
| Wind Survival | >150 MPH |
| RoHS Compliant | Yes |
Specifications:, Datasheet:, Click Here, Manual:, Click Here,
Superior performance Light weight Durable UV-stable, UL flame rated radome ...ngHobbies
SHORT TX HARNESS FOR 900MHZ, 1.2GHZ AND 1.3GHZ TRANSMITTERS
This 15 cm FPV cable harness offers connection breakout for the folowing types of transmitters:, 900Mhz 800mW, Instructions:, Plug the white connector end to the connector coming out from the transmitter and supply power through the red JST type connector., Connector 1 (Video):, , Connector 2 (Audio):, , Connector 3 (Battery):, Red - Battery positive lead,
1.3GHz 400mW 1.3GHz 800mW 1.3GHz 1500mW LawMate 2.4GHz 1000mW LawMate ...ngHobbies
NGH BATTERY MONITOR
| Dimensions | 105 x 70 x 20mm |
| Weight | 110gr. |
| LCD Display | 128*64 pixels |
| Stanby power consumption | <2mA |
| Accepts data from chargers with an USB port like | EV, IMAX, G.T, TP, Hyperion, Robbe, Triton |
The 4 operation modes are:, it will collect data and display a graph of the charging or discharging cycle to accurately monitor the individual cell voltages and the balancing process., Features:,
The NGH Battery monitor is a 4 in 1 battery ...ngHobbies
KX 171 LOW VOLTAGE CAMERA (NTSC)
| Imaging | 1/3" SONY CCD |
| Number of Pixels | NTSC |
| Scanning System | NTSC |
| Horizontal Resolution | 420 TV Line |
| Auto White Balance S/N Ratio | Better than 46dB |
| Gamma Characteristic | 0.45 (AGC Off) |
| Minimum Illumination | Day |
| Power | 5-15V±10% DC @ 100mA |
| Dimension | 20 X 20mm |
| Weight | 22g |
Shipping with: f: 3.6mm mini lens,